Blog

How to stop buddy punching (proxy attendance)

To stop buddy punching, make each punch prove the person was there: use a face or fingerprint machine instead of cards or PINs, or a phone selfie inside a GPS geofence for staff without a machine. Then check the few punches that still get through, such as card and PIN punches. No method is perfect, so the method and the checks work together.

· Attendance · 3 min read · By the OTOMATE team

What buddy punching looks like

Buddy punching, or proxy attendance, is one person marking attendance for another. In a register book it is a signature. With a card machine it is a friend’s card in your pocket. With a PIN it is a number shared on WhatsApp. With a phone app it can be a borrowed phone or a fake location.

It matters because attendance becomes pay. A worker marked present for two extra days a month is paid for them, and their overtime may be too. Across 100 workers, a few proxy punches a week add up quickly.

Fingerprint, face, card, PIN and selfie with GPS compared

MethodStops proxy punching?Where it fails
Card (RFID)NoCards are easy to lend. Use cards for doors, not for attendance on their own.
PIN or passwordNoA number is shared in seconds.
FingerprintMostlyWorn or cut fingers (masons, loaders, cooks) fail to read; staff then get a card or PIN “just for now”. Dirty sensors cause queues.
FaceMostlyContactless and quick. Cheap units without liveness checks can be fooled by a photo; check the model. Bright sun behind the person causes misses.
Selfie with GPS on the phonePartlyNeeds a smartphone. Proves place and gives a photo for review, but someone must look at flagged punches.
Supervisor marks on paperDepends on the supervisorHard to audit later.

The weak spot in most biometric set-ups is the exception. A fingerprint machine stops proxy punching until someone’s finger fails and they are given a card. Six months later, a fifth of the staff punch by card.

Which method to choose

Factory or site with manual work
A face machine. Fingerprints wear down with heavy work, and face reading is contactless.
Office or shop
Fingerprint or face. Both work well with clean hands and good light.
Field staff, sales and service
Selfie with GPS on the phone, in field mode, so the location is saved with each punch.
Several small sites without a machine
Selfie with GPS in office mode, with a geofence around each site.
Doors
Card or face for the door; attendance from the face or finger, not the card.

Many eSSL and ZKTeco machines let you set the verification mode on the machine, for example face only, or card plus fingerprint. Use it for anyone who has a card, so the card alone is not enough.

Checks that catch the rest

  • Look at how each punch was verified. Card and PIN punches should be rare. A person whose punches are all card is the first one to check.
  • Re-enrol failed fingers. Enrol two or three fingers, or move that person to face, rather than handing out a card.
  • Walk the floor against the live list. Once a week, compare the people in front of you with the list of who is in right now.
  • Watch patterns. Two people who always punch within a minute of each other, or a punch at the gate when the person was seen elsewhere.
  • Review flagged phone punches. Punches outside the geofence or with poor GPS accuracy, and their selfies.
  • Write it into your policy. State that punching for someone else is misconduct for both people, and apply it the same way every time.

How OTOMATE helps

OTOMATE records how each machine punch was verified: fingerprint, face, card, PIN, palm or app. The attendance log shows it beside every punch, and the console and app show who is in right now, live, so a floor check takes a minute. For phone punches, OTOMATE’s server refuses fake locations that Android reports from mock-location apps, fixes less accurate than your setting, punches outside the branch geofence in office mode, and repeat punches within a minute. HR can open each selfie and mark the punch approved or flagged. OTOMATE does not run face recognition on selfies, so a person still has to look.

More on the phone side in the guide to selfie attendance with GPS.

Questions people ask

Something else? Call +91 90536 35607 or write to hello@otomateworld.com.

What is buddy punching?

One employee marking attendance for another, with their card, PIN, phone or signature, so the absent person is paid as present.

Does a fingerprint machine stop proxy attendance completely?

It stops most of it. The gap is the exception: staff whose fingers do not read are often given a card or PIN, and those can be shared. Re-enrol them or move them to face instead.

Is face attendance better than fingerprint?

For manual work, usually yes, because worn fingers do not matter and nothing is touched. Choose a model with a liveness check so a photo cannot be used, and avoid placing it facing bright sunlight.

Can staff fake their location in a GPS attendance app?

Some try with mock-location apps. OTOMATE refuses locations that Android reports as mocked and fixes that are less accurate than your setting, and it checks the geofence on the server, not on the phone.

Can I see which punches were made with a card?

Yes. OTOMATE shows the verification method for every machine punch in the attendance log: fingerprint, face, card, PIN, palm or app.

See it on your own machines

Book a free demo. We connect one of your machines with you on a call, and you watch your own staff’s punches arrive.